Rat soluble CD8 molecule (sCD8) ELISA kit

Rat soluble CD8 molecule (sCD8) ELISA kit

(Used in serum, plasma, cell culture supernatant and biological fluid)

principle

This experiment uses the double antibody sandwich ABC-ELISA method. The anti-rat sCD8 monoclonal antibody was coated on the enzyme plate. The sCD8 in the standard and the sample was combined with the monoclonal antibody. Biotinylated anti-rat sCD8 was added to form an immune complex and attached to the plate. Horseradish peroxidation The enzyme-labeled Streptavidin is combined with biotin, the substrate working solution is added, and the final solution is added with sulfuric acid. The OD value is measured at 450nm. The sCD8 concentration is proportional to the OD value. concentration.

Kit composition (stored at 2-8 ° C)

Coated Wells

96 wells

Enzyme Conjugate

12ml

10 × Sample Buffer

12ml

20 × concentrated washing solution (Wash Buffer)

50ml

Standards (Standards): 2ng / bottle

2 bottles

Substrate working solution (TMB Solution)

12ml

The first antibody working solution (Biotinylated Antibody)

12ml

Stop Solution (Stop Solution)

12ml

Prepare reagents and collect blood samples

1. Collect specimens: serum, plasma (EDTA, citrate, heparin anticoagulation), cell culture supernatant, tissue homogenate, etc. as soon as possible, stored at 2-8 ℃ for 48 hours; longer time must be frozen (-20 ℃ Or -70 ℃), avoid repeated freezing and thawing. Before the determination of all specimens, use the specimen dilution to make a 1:10 dilution (take 20ul, add specimen dilution 180ul, and dilute 10 times).

2. Standard solution preparation: add 0.5ml of distilled water to mix well before use to make a solution of 4000pg / ml. Set 8 standard tubes, and add 300ul of sample dilution to each tube. In the first tube, add 300 ul of the standard solution of 4000 pg / ml and mix it. Then aspirate 300 ul with the pipette and move to the second tube. Repeat the double dilution in this way, draw 300ul from the seventh tube and discard. The eighth tube is a blank control.

3. The 10 × specimen dilution is diluted 1:10 with distilled water (example: 1ml concentrated dilution + 9ml distilled water).

4. Washing solution: 1:20 dilution with redistilled water (example: 1ml concentrated washing solution is added with 19ml of redistilled water)

Testing procedures

1. Add sample: add 100ul of standard or sample to be tested to each well, mix the reaction plate thoroughly and place at 37 ℃ for 120 minutes.

2. Wash the plate: wash the reaction plate 4-6 times with the washing solution, and print it on the filter paper.

3. Add 100ul of the first antibody working solution to each well. The reaction plate was mixed thoroughly and then placed at 37 ° C for 60 minutes.

4. Wash board: same as above.

5. Add 100ul of enzyme-labeled antibody working solution to each well. Place the reaction plate at 37 ° C for 30 minutes.

6. Wash board: same as above.

7. Add 100ul of substrate working solution to each well, and place in a dark place at 37 ℃ for 15 minutes.

8. Add 100ul of stop solution to each well and mix well.

9. Measure absorbance at 450nm with a microplate reader within 30 minutes.

Result calculation and judgment

1. All OD values ​​should be calculated after subtracting the blank value.

2. With the standard products 2000, 1000, 500, 250, 125, 62.5, 31.2, 0 pg / ml as the abscissa, and the OD value as the ordinate, draw a graph on the graph paper and draw a standard curve.

3. Find the corresponding sCD8 content on the graph according to the OD value of the sample, and then multiply the dilution factor by 10.

Kit performance

1. Sensitivity: The minimum detection concentration of sCD8 is less than 15pg / ml.

2. Specificity: simultaneous detection of recombinant or natural rat sCD8. Does not cross-react with other cytokines in rats.

3. Repeatability: The coefficient of variation within the board and the board is less than 10.6%.

Precautions

1. The above standard holes and samples to be tested are recommended to be re-holes, and the standard curve should be made at the same time for each measurement.

2. The washing process is critical. Insufficient washing will lead to an increase in accuracy error and OD value.

3. After opening the slats, the remaining slats should be sealed again to keep the slats dry.

4. This kit should be stored in a 4oC refrigerator.

5. This kit is for scientific research only, not for clinical diagnosis!

Black Film Faced Plywood

Product name 18mm film faced Marine Plywood
Thickness 18mm
Size 1220×2440mm
Glue melamine/phenolic
Density 540KG/M3-600KG/M3
Surface finish Black/brown/red film,anti slip.
Material Poplar,pine,hardwood,combi
Quantity
20GP container(pallet packing) 8 pallets
40GP container(pallet packing) 16 pallets
40HQ container(pallet packing) 18 pallets
Payment terms 30%T/T in advance,70%T/T or L/C at sight of B/L
Delivery time  within 15 days after receiving deposits

Black Film Faced Plywood

Black Film Faced Plywood,Black Film Faced Plywood Sheet,Black Film Faced Marine Plywood,Black Poplar Core Film Faced Plywood

Shouguang Bailing Wood Industry Co., LTD. , http://www.bailingfurniture.com