Post-Binding Technology 1000 Questions--Basics Part Seven

154. What is the spread match?

A: An ancient manning method using manual soft sheets and signatures. When collating, the number of the first or last edition of the signature will be trapezoidal. Then the second edition will be covered with a trapezoid along the first edition. After the signatures are successively traversed, they will be drawn in the trapezoidal order. It will become a volume, how many volumes will be assigned to each trapezoid (Figure 28-3).

155. What is your hands?

A: It is a manual method to use both hands at the same time. Hands began in the early 1960s and were used as a method used in the Shuanglianshushu. They were later used for the collation of books within 8 posts. During the operation, first place the posts in correct order, and place 2 to 4 posts up and down, 2 or 4 posts to the left and right, and use the 2 and 3 fingers of both hands to pick up the book from the book (Figure 28- 4). This sorting method is fast (it can increase the output more than double), labor saving, and can be prevented from being worn by hand after it is fitted.

156. What is a pull match?

A: Pulling is a method used to match books with large numbers of single and double members and with a large number of posts. Each page (or 500 pages on a single page, 250 sheets on a double page) of a page or a booklet will be stacked in the order in which the pages will be placed. Lay out with matching calendars, invoices and other processing (Figure 28-5).

157. What is pulp back?

A: Pulp back is a book that will be filled with a good book, tied together, smear a layer of adhesive on the back of the book, so that scattered pieces of the book stick together to facilitate the processing of the next process.

158. What is the cost?

A: The split book refers to the entire bundle of books that will be backed up and dried, and a separate processing to facilitate the next process of ordering or bag cover.

159. What is a cut?

A: The cut book refers to sticking a layer of cardboard on the back of the pulp and drying it. Then use a knife to cut the book off the book.

160. What is package book?

A: The package is also called the cover. It is the book block that will be well-ordered or divided, and the adhesive is evenly coated on the back of the book and the back of the book, and the cover is glued to become a complete book.

161. What is hot back?

Answer: The book will be glued to the cover, and hot presses will be used to make the spine flat, hot and hot.

162. What is a saw cut?

A: Sawing is the use of a manual saw or slot saw to saw a certain depth, width, and number of grooves in the book spine. The role of the kerf is to allow the binder on the book to penetrate through the groove into the innermost sheet of the booklet crease to form a semi-mechanical wireless glue binding method.

163. What is the line?

A: Refers to the paperback book package, due to various reasons caused by the back of the book and the spine of the surface of the book projecting a line (Figure 29).

164. What is a small page?

Answer: After the books have been bound and cut, due to various reasons in the processing of semi-finished products, some pages in the book are retracted into the book. Since the retracted pages are smaller than the normal size of the books, they are called small pages.

165. What is broken?

Answer: The broken book refers to the book that has been cut into finished products. Due to various reasons, the cover on the upper and lower ends of the book is torn.

166. What is Zhang Guan Li Dai?

A: Refers to the phenomenon of binding the cover of a book to the book block of the second book and binding the cover of the previous book to the lower book or other book blocks in the binding process.

167. What is milling back?

A: The book will be equipped with a good book on the back of the mill with a milling cutter into a casual or groove-like, in order to glue after infiltration into a wireless adhesive book processing.

Second, a variety of loading process part

168. What is the flat iron wire ordering process?

Answer: A process of binding paperback books with metal wire.

Semi-finished product sheet start: hit page â†’ open material â†’ folding â†’ set, insert, stick page â†’ waxing â†’ page matching â†’ hitting a book, tied book, pulp back â†’ dry copy â†’ book â†’ semi-finished product inspection â†’ â†’ brush adhesive â†’ Package cover â†’ hot back dry â†’ cut book â†’ finished product inspection â†’ packaging label.

169. What is a paperback wireless glue binding process?

A: A process for binding paperback books with glue.

Semi-Finished Product Sheets Start: Hit Pageâ†’Opening Materialâ†’Fold Sheetâ†’Setsã€Insertsâ†’Pagesâ†’(Bump, Bundle, Pulpâ†’Drying Paper) on the Adhesive Packing Machineâ†’Storage Bookâ†’Zhen Qiâ†’Book Block Clamping and Fixingâ†’ Milling back â†’ gluing â†’ sticking cover â†’ booklet clamping molding â†’ publishing â†’ cooling and drying â†’ cut book â†’ finished product inspection â†’ packaging labeling.

170. What is a paperback lock stitching process?

Answer: A process of binding paperback books with a lock thread.

Semi-finished product sheet start: hit page â†’ open material â†’ sticky, cover page â†’ glue ring liner â†’ match page â†’ lock line â†’ semi-finished product inspection â†’ flattening â†’ hitting binding book â†’ coating adhesive â†’ sticky gauze or paper jam â†’ dry copy â†’ coating Adhesive â†’ Cover (the book with the mouth cut before the first mouth, then cut both ends of the package cover) â†’ hot back (or cover the machine with hot melt adhesive cover) dry â†’ cut book â†’ finished product inspection â†’ packaging Paste logo.

171. What is the saddle stitching process?

A: A process for binding saddle-stitched booklets in a single machine.

The semi-finished product sheet starts: hit page â†’ open material â†’folding â†’ nesting page â†’ hitting â†’ book â†’ bound book or flattening â†’ cut book â†’ finished product inspection (or spot check) â†’ packaging label.

172. What is a hardcover book process?

A: A process that uses a single machine and hand-made hardcover book. The process is divided into three lines, namely the book block, book cover, and nesting.

Book core processing process: semi-finished product sheet start â†’ hit page â†’ open material â†’ sticky, cover page â†’ adhesive ring liner â†’ page â†’ lock line â†’ semi-finished product inspection â†’ flattening â†’ stacking flattening â†’ cut book â†’ binding book â†’ coating adhesive ~ â†’ Drying copy â†’ Cut book â†’
Coated adhesive â†’ æ‰’ circle â†’ ridge â†’ coating adhesive â†’ wet â†’ adhesive bookmark ribbon â†’ adhesive plug cloth â†’ coating adhesive â†’ sticky cloth backing â†’ sticky paper back paper â†’ adhesive coating â†’ sticky cheese paper.

Book closure processing process: calculate the size of the book shell material â†’ open material â†’ coating adhesive â†’ group shell â†’ shell shell plug angle â†’ flattening â†’ natural drying â†’ hot stamping.

Coupling processing process: Coated adhesive in the coating â†’ sleeve â†’ pressure tank â†’ lining â†’ flattening â†’ natural drying â†’ finished product inspection â†’ package protection â†’ packaging label.

173. What is the assembly process?

A: Line equipment, also known as ancient line equipment, the process is divided into three lines, are manual operations.

Book block processing flow: Printing semi-finished productsâ†’Materials (collision)â†’(Opening materials)foldingâ†’Collecting pagesâ†’Checking the qiqiâ†’Pressing/flatteningâ†’Columnsâ†’Punchingâ†’Styling the paper nailsâ†’Fitting the coverâ†’Cut the bookâ†’Package Cornerâ†’Replicateâ†’Punchâ†’Threading Staplesâ†’Stick Bookmarksâ†’Printed Book Root.

Correspondence processing flow: Calculate and cut the book letter each material â†’ coating adhesive â†’ group shell â†’ shell glue letter â†’ slotting â†’ manufacturing pin hole, pin, bone tag â†’ coating adhesive â†’ lining strip â†’ coating adhesive â†’ sticky Liner â†’ Flattening â†’ Natural drying â†’ Sticky label.

Fitting processing flow: Checking â†’ Checking â†’ Fitting the letter â†’ Packaging â†’ Labeling.

174. What is a luxury installation process?

A: A process that binds books with expensive binding materials and complex manufacturing processes. The process consists of three parts: book block, book cover, and nesting.

The book has a processing process: semi-finished product sheet â†’ hit page â†’ open material â†’ folding â†’ sticky cover page â†’ sticky lining material â†’ package lining â†’ adhesive ring lining â†’ page matching â†’ lock line â†’ semi-finished product inspection â†’ flattening â†’ binding binding Agentâ†’ Drying copyâ†’ Cut front mouthâ†’ Cut flowers mouthâ†’ Cut two endsâ†’â†’ Cut books, roll gold mouthâ†’ Round roundâ†’ Pick up ridgesâ†’ Coated adhesivesâ†’ Sticky ribbonsâ†’ Locking rope head (or sticky plug cloth) â†’ Coated adhesives â†’ adhesive backing and backing paper â†’ adhesive coating â†’ adhesive bobbin paper.

Book closure processing process: calculate, match the book cover of the various materials â†’ coating adhesive â†’ group shells â†’ bamboo section â†’ shell plug angle â†’ flattening â†’ natural drying â†’ hot stamping â†’ coating adhesive lining.

Coupling processing: Coated adhesive â†’ (to be coated in the diameter of the binder paper) sleeve â†’ pressure tank â†’ coating adhesive â†’ sticking lining and lining â†’ flattening â†’ natural drying â†’ finished product inspection â†’ package Sealing â†’ Packaging labeling.

175. What is a wireless glue binding production line process?

A: The wireless glue binding production line is a production line for processing wireless glue binding books made up of three major units. The process flow is:

Paging unit: Set each stop â†’ store posts â†’ attract posts â†’ posts â†’ set posts â†’ into the package cover unit: into the original and Zhen Qi â†’ clamp positioning â†’ back iron â†’ glue â†’ sticky back paper â†’ second coating Glue â†’ Sticky Cover â†’ Clamping Binding Finishing â†’ Turning Down the Book â†’ Transferring and Naturally Drying â†’ Entering the Cut Book Section: Cut â†’ Cut Finished Product â†’ Automatic Stacking â†’ Packaging Labeling.

176. What is the process of riding a chain production line?

A: The saddle-stitching linkage production line is a production line consisting of three units designed to bind saddle-stitched books. The process flow is as follows.

Page-laying unit: Set each block â†’ store post â†’ attract post â†’ post â†’ block post â†’ divide post â†’ tap post â†’ transfer â†’ enter the book unit: wire delivery â†’ shred wire â†’ molding â†’ book â†’ catch hook â†’ Book throw â†’ transfer â†’ enter the cutting unit: Positioning â†’ Cut Book â†’ Book â†’ Count â†’ Finished Product â†’ Packaging â†’ Label.

Table Series
Table Series,College Classroom Desk,Wooden Reading Table,Desks With Wheel
AU-PINY FURNITURE CO., LTD , https://www.jiangmenaupiny.com