The redwood fans who have not been to the factory must be very curious, how is a piece of rosewood furniture made? Why is every piece of rosewood furniture worth a lot of money, besides the scarcity of materials, are there other factors? Choose furniture to see The same two pieces of furniture, the same materials, but the quality of the material is different, its value is also different, the same is sandalwood rosewood, the finest material to be five or six hundred thousand tons, the medium material to be three or four hundred thousand tons, the next If you want to use more than 200,000 tons, choose different materials, the cost will be different. If you use good materials, the furniture will rarely be patched, the materials used are not good, and the patches will be more, such as a case, its The panel is two pieces of the fight, it is more precious than the three fights, because the price of the two pieces of the material is high. For example, the top box of this rosewood Yunlong pattern is made of large materials, and there is almost no applicator. The material is selected when the material is selected. The seven-layer dragon pattern is hand-carved, and the thickness of the panel is 5 cm. The panels of a typical top cabinet are not as thick. Cutting and drying After selecting the material, it is necessary to open the material and dry it. The material is very particular. It depends on the texture of the wood. Try to use the good pattern on the large surface of the furniture. Pay attention to the consistency of the color of the whole set of furniture to ensure the fullness of the wood. Use, or take this top cabinet as an example, this top cabinet from front to back, from the inside out, the choice of wood is very unique, the panel pattern is consistent, seamless. The wood drying plant generally uses steam drying method. This method can basically adapt to the northern winter heating and summer humid climate. Such drying equipment is not available in general small factories. The equipment is about ten thousand. æ¦«å¯ and jigsaw determine the quality of furniture The æ¦«å¯ structure is the essence of classical furniture. Good furniture must be made according to the traditional æ¦«å¯ structure. The furniture that comes out of this way is strong and beautiful. The slab is the combination of two boards. The manufacturer is between the two boards. It is necessary to use the æ¦«å¯ structure, so that the board that is put out is firm and firm. If the two boards are sticky for the sake of saving trouble, then it is a little bit uncomfortable. According to the strictest 榫 between the top box panels and the board of the Yunlong pattern. The å¯ structure is combined to make the two boards tightly joined together. Engraving is the most technically active For example, a 7-meter-long, 40-centimeter-long seven-layer carved Yunlong board used on the top cabinet, the engraving process has to go through four steps of roughing, polishing, polishing and fine work. The blanking is to reflect the shape of the design; to repair the light is to treat the details with care and to express the artistic effect; to polish, it is to smooth out the burrs of the carving; the fine work is to engrave on the basis of the other three steps. Thin lines come, for example, carving dragon scales, landscapes, etc., which process is not in place, this set of furniture is not beautiful. In terms of time to subdivide, the above-mentioned board, 45 work for roughing, 46 work for repairing, 15 work for polishing, and 5 to 6 work for fine work; this board is just engraving To have more than one hundred workers, one piece of furniture is full of the hard work and sweat of artisans and designers, and its artistic value and collection value are reflected in the carving work. Assembly and scraping, fine grinding also takes a lot of work After the engraving and boring structure is basically completed, the rest is assembled and scraped. For example, the top box of the Yunlong pattern, the assembly takes two people a month's effort; the shaving is to put the burrs inside and outside the furniture. Remove it, this also takes more than 30 jobs. After the scraping, it is fine grinding. This time, all aspects of the furniture must be polished, and the work should be about 50~60. After fine grinding, it is also waxed, and a piece of furniture is born after waxing. A cloud dragon top box is used for five to six months from the opening to the finished product. Each process is full of the hard work and wisdom of the producer. When we use these furniture, you will always appreciate the greatness and tenacity of the workers. (The author of this article is the chairman of Hongri Classical Furniture Co., Ltd.) Leather Chair,Leather Lounge Chair,Leather Desk Chair,Brown Office Chair Feat Top International(China) CO.,LTD , https://www.feattop.com