Plastic composite steel plate It is a soft or semi-rigid polyvinyl chloride plastic film coated with 0.2-0.4mm on steel plate or profiled steel plate, which is divided into single-sided and double-sided coating. It has the characteristics of insulation, wear resistance, corrosion resistance and oil resistance; it can be used as wallboard and roof panel. Decorative panels Is it sliced ​​or cut into 0.2# 1 by natural wood? The sheet is made by laminating and pasting on a substrate such as plywood, fiberboard, particleboard or the like. This material has a clear texture and natural color and is a high-grade decorative material. Calcium composite board It is made of high-pressure polyethylene as a substrate, adding a large amount of light calcium carbonate and a small amount of additives, and is made by processes such as mastication, hot pressing and foaming. This kind of plate is light, soundproof, heat insulation and moisture proof. Mainly used for ceiling tops. Medium density fiberboard Fiberboard Divided into three types: hard fiberboard, semi-hard fiberboard and soft fiberboard. Hard fiberboard is mainly used for ceiling and partition wall panels. The surface of the board is drilled to form various patterns, and various coatings are applied on the surface to make the decoration effect better. Hard fiberboard sound absorption, waterproof performance, sturdy and durable, easy to construct. Yellow pineapple The wood is lustrous, the annual rings are obvious and uniform, the material is soft, easy to dry and process, the color and pattern are very beautiful, the paint and cementing performance is good, it is not easy to crack, and the corrosion resistance is good. It is the material for high-grade furniture. Elm Aroma, anti-corrosion, anti-insect, lighter material, not easy to deform, easy to process, smooth cut surface, beautiful color after painting. Elm The texture is hard, the ratio is high, the strength is high, and the structure is dense. It is resistant to moisture, abrasion, and is not easy to be cemented. It has good coloring performance, rough texture, thick tubular cells, obvious wood rays, and is not easy to dry. Generally, it can be used for wood flooring or furniture. Ash The material is slightly hard, the pattern is beautiful, the corrosion resistance, water resistance is good, easy to process, toughness, cemented paint, good coloring performance, good decorative performance, and is a kind of wood which is used more in the decoration materials. Melamine board The full name is melamine impregnated film paper veneer wood-based panel. It is a decorative board which is made by immersing paper with different colors or textures in melamine resin adhesive, drying it to a certain degree of curing, and laying it on the surface of particleboard, medium density fiberboard or hard fiberboard, and hot pressing. PE calcium composite panel The main raw materials of the calcium plastic plate are resin, filler, foaming agent and the like. It is a raw material plastic mixer mixing and evenly extruding the sheet material in a compression molding machine to expand and heat the mold, and the sheet material is immediately puffed into a calcium plastic foam board. The expanded longitudinal expansion is 1.7 times and the thickness is expanded by 2 times. The foamed sheet in the hot mold was immediately vacuum formed by vacuum. The specification is generally 500mm × 500mm and the thickness is 6mm. Aluminum composite panel It is made of high-pressure polyethylene as a substrate, adding a large amount of aluminum hydroxide and an appropriate amount of flame retardant, and is made by processes such as mastication, hot pressing and foaming. This kind of plate is light, soundproof, heat insulation and moisture proof. Mainly used for ceilings and wall surfaces. Plywood The plywood is a three-layer or multi-layered plate-like material which is formed by cutting a wooden section into a veneer or by cutting into a thin wood by wood, and then bonding with an adhesive, usually using odd-numbered veneers and making adjacent veneers The fiber directions are vertically glued to each other, and the front and inner plates are symmetrically disposed on either side of the center layer or the core. Slim wood veneer It is made into a 0.1-0.5mm thick sheet with water ash, willow wood, color wood, birch, etc., and is glued to the base material of the plywood. The pattern is beautiful and the decoration is good. Liu Anmu The material is light and heavy, the structure is slightly thick, easy to process, the cementing performance is good, the drying process is slightly warped and cracked, and it is mostly used for making plywood or plywood. Chinese fir The material is light and light, easy to dry, easy to process, rough in cut surface, medium in strength, easy to split and has good adhesive performance. It is a medium-grade wood which is currently used more commonly. Elm The wood is shiny, the structure is slightly thick, the drying speed is slow, it is not easy to warp, it is easy to process, and the nailing force is strong. Basswood The material is soft, oily, wear-resistant, corrosion-resistant, not easy to crack, fine wood grain, easy to process, strong toughness. It has a wide range of applications and can be used to make decorative materials such as wood, blockboard and wooden crafts. Redwood The material is hard, not easy to process, not easy to dry, strong nail holding power, good cementation and paint performance. Suitable for decorative panels and high-end furniture. Bagasse chipboard Sugarcane bagasse is the residue after sugar-making. After the bagasse of bagasse is removed, its chemical composition is similar to that of wood. It is a good raw material for making plates. Because of the small specific gravity of bagasse and good fiber quality, the obtained plate has high strength and light weight. The water swelling rate is low. It is a medium-density particle board with smooth surface, beautiful color, good dimensional stability, good machinability and decorative properties. Uses: Applicable to furniture, construction, carriage, ship, packaging and other production industries. Gradient structure particle board From the surface to the center of the particle board, the shavings gradually changed from small to coarse, and the surface layer did not change significantly, and it was paved with an airflow paver. The surface is fine and smooth, high in strength, good in dimensional stability, and has good machinability and surface decoration. Oriented Strand Board (OSB) Oriented strand board is a kind of slab that is processed by special equipment with small diameter material, thinned wood, wood core, board skin, branch material, etc., by special equipment, 40mm, 70mm, width 5mm, 20mm, thickness 0.3mm, 0.7mm. , sizing and special equipment A wood-based panel after hot-press forming after the core layer slab is oriented in a crisscross orientation. Because OSB adopts special technology and many special equipments, it has the advantages of high flexural strength, small linear expansion coefficient, good dimensional stability, strong nail holding ability and easy surface decoration. It is widely used in packaging, construction and vehicles. Shipbuilding and other industries. Ash (White) Tough and elastic, the sapwood is pale milky white, and the heartwood varies from light brown to dark brown. The wood grain is obvious and coarse. It is easy to process and is easily bent by steam. Use luxury furniture, flooring, mouldings, fine woodwork, sports equipment, tool handles, etc. Ash Tough and elastic, it is milky white or pink with pink. The processing is simple, it is easy to bend by the steam method, but it is easy to decay, so it is not easy to use for appearance. Fireproof board The fireproof board is a decorative board made of a silicon material or a calcium material as a main raw material, mixed with a certain proportion of fiber materials, lightweight aggregates, binders and chemical additives, and subjected to autoclaving technology. It is a new type of material that is being used more and more, and its use is not only due to fire prevention. The construction of fireproof board has higher requirements for sticking glue, and the price of fireproof board with better quality is more expensive than decorative panel. The thickness of the fireproof board is generally 0.8 mm, 1 mm and 1.2 mm. Large core board The large core board is a special sandwich plywood. It is made up of parallel strips of the same thickness and different lengths, and is closely spliced. It is generally a five-layer structure. The vertical direction of the large core board (differentiated by the direction of the core material) is poor in bending resistance, but the transverse bending strength is high. Decorative panel Decorative panels are commonly known as panels. It is a decorative board with a single-sided decorative effect, which is made by cutting the solid wood board into a thin veneer with a thickness of about 0.2 mm and using a splint as a base material. It is a special way of splinting and has a thickness of 3 centimeters. Decorative panels are a high-end finishing material that is currently different from blending practices. Splint Also known as plywood, three or more layers of one millimeter thick veneer or sheet adhesive are hot pressed. It has the advantages of light material, high strength, good elasticity and toughness, impact resistance and vibration, easy processing and finishing, and insulation. Peachwood The sapwood is grayish-brown and the core material is light gray-brown. Elm The sapwood is yellowish white and the core material is dark gray. Three-layer structure particle board The surface layer is made of thinner and smaller special micro-planing, and the core layer is thicker and larger. Three paving heads are used. Particleboard (Flakeboard) Particleboard, also known as particle board, is a dry mix (such as wood shavings, flax, bagasse, etc.) such as wood shavings made of wood or non-wood plants with or without rubber and excipients. A thin plate made by hot pressing. The particleboards are classified as follows: 1, according to the use of: divided into Class A particle board and Class B particle board; 3. According to the surface condition: unfinished particle board: a. sanding particle board; b. unsanded particle board. Finished particleboard: a. impregnated paper facing particleboard; b. decorative laminate facing particleboard; c. veneer facing particleboard; d. surface coated particleboard; e. PVC facing particleboard; Toner Cartridge For Canon,Best Canon Toner Cartridge,Compatible Laser Toner Cartridge,Premium Compatible Toner Cartridge jiangmen jinheng office equipment Co. Ltd. , https://www.jm-jinheng.com
Density fiberboard is a kind of artificial board. It uses plant fiber as raw material, shaving, fiber separation, slab forming (mixing resin glue and additive paving), and making cellulose and hemicellulose under hot pressing. A sheet of plastic formed by lignin.
2, according to the structure of the particle board: a. single-layer structure particle board; b. three-layer structure particle board; c. gradient structure particle board; d. oriented particle board; e. waffle particle board; f. molded particle board;
4. According to the raw materials used: a. wood particle board; b. bagasse chipboard; c. linen chipboard; d. cotton slab particle board; e. bamboo particle board; f. cement particle board; g. gypsum particle board;
5, according to the manufacturing method: a. flat pressed particle board; b. extruded particle board.